AG Neovo DS-55 Spécifications

Installation Notes Please make sure you have a solid installation. As shown in the picture. You can install the display set by screws x 8 (M4x15mm) 8

Package Content Unpacking • This product is packed in a carton, together with the standard accessories. • Due to the size and weight of this displ

Accessories Dual-sided Display x1 Power Cord x1 PC Box x1 (with 24V&12V line) 10 Remote Controller x1 (Battery : CR 2025 3V)

Over View Front View Top View Diagonal View Side View 11

Over View 1. Display (Dual-sided) 2. Display Set 3. Remote control sensor (Dual-sided) 4. Mounting hole x 8 (single side have 4) 5. I/O cover x 3 1 2

Setting Up The Display Step1 : Putting the dual-sided display upside While the display put upside , the screw will be seen on the left. 13

Step2 : Remove the three I/O covers on the sides Remove I/O cover screws x 3(M3x6mm) 14

Step3 : Remove the downside cover Tear down the downside cover. screws x 10(M3x6mm) 15

Step4 : Connect Power Box to Dual-sided Display Power Box Dual-sided Display 24V*1 Red line (10 pin) 12V*1 Yellow line (8 pin) 1 2 16

Connect the 24V (10 pin) power line 1 Connect the 12V (8 pin) power line 12V*1 Yellow line (8 pin) 24V*1 Red line (10 pin) 2 1 2 17 Step4 : Connect

• Important Safety Instructions………………………….1 – Safety precautions and maintenance………………...1 – Use………………………………………………………………4 – Installation Not

Step5 : Connect by HDMI connector Plug two HDMI cables into the cabinet. And ensure that all cable plugs are firmly fitted to the equipment jacks. HDM

Step6 : Reinstall the downside cover and I/O covers 1 Reinstall the downside cover. screws x 10(M6x30mm) Reinstall the other two I/O covers which are

Plug in the power cable and turn on the AC power switch. AC in / switch Step7 : Connect the power cord Power Box 20

Step8: Using the Remote Control No. Key Descriptions Power Power on/Power off Menu Into OSD module Menu Right Menu Left Menu Up Menu Down Exit Me

Luminance Press MENU to select one of the following, and then press “RIGHT” or “LEFT” to select the desired level, ---Brightness1: Range: 0~100 ; De

Color Press MENU to select one of the following, and then press “RIGHT” or “LEFT” to select the desired level, ---Color Temperature: Range: 6500K, 9

Press “MENU” into the OSD Setting Menu, and then press “UP” or “DOWN” to select the item, at last press “EXIT” to leave menu : 24 OSD Settings Press

Press “MENU” into the OSD Setting Menu, and then press “UP” or “DOWN” to select the item, at last press “EXIT” to leave menu : 25 Setup Press MENU

Trouble shooting Symptom Possible Cause Remedy No picture is displayed 1. The power cord is disconnected. 2. The main power switch on the back of th

LCD Display 55” Model name DS-55 Screen size 55 inch (diagonal) Resolution 1920 x1080 (Pixel) Display Area 1209.6(H) x 680.4(V) Contrast Ratio 3000:1

Safety precautions and maintenance WARNING: Use of control, adjustments or procedures other than those specified in this documentation may resul

Product Dimensions 28 A,B,C: I/O covers

Safety precautions and maintenance Maintenance: • To protect your display from possible damage, do not put excessive pressure on the display. • Unpl

Safety precautions and maintenance Read and follow these instructions when connecting and using your display: • Unplug the display if you are not goi

Use • Don’t turn the ventilation hole of Power Box upside down. As shown in the picture below. The ventilation hole of power box It is prohibite

Use • When you install the display, please don’t use the “bottom side” I/O hole and open the I/O cover . As shown in the picture below. The “bot

Use Disconnect devices: • For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 6 Re

Installation Notes There have 8 mounting holes on the side of the display set (M4x15mm) F 7